Friday, May 23, 2014

5/19/2014 Solenoid & Magnetic Field in Motion

Solenoid
In this experiment, we are rolling turns of wire on a plastic rod and place it around the magnetic field sensor to measure the magnetic field that created by moving current.  

Recorded magnetic field created by different turns of coil.  Base on the data to calculate the length of solenoid which is many turns of coil.  But the values of the strength of the magnetic field were not very reliable because of the orientation of the sensor.

Measured data by Professor Mason.  

Magnetic Field in Motion
We were given a coil of wire, galvanometer, and bar magnet in order to experiment with electromagnetic induction. 

We are moving the bar magnet in and out of coil of wire in this experiment.  Base on observation we found that factors such as the number of coils and the velocity in which we moved the magnet in and out of the coil contributed to the amount of current we measured.  





Sunday, May 18, 2014

5/15/2014 Finding The Magnetic Field of Earth

Finding Earth Magnetic Field
We are connecting power supply with coil to produce magnetic field.  Base on the know values such as current, turns of coil, and change of angle on the compass when the magnetic field created by the coil.  

Recorded experiment data.  In order to determine this we used the deflection of the compass at a know current and solved for the magnetic field of the earth by dividing the magnetic field of the coil by tangent of theta.

Once we fit a linear line onto our data that the slop of the data set would be the magnetic field of the earth which was about 1*10^-5 T.

Tuesday, May 13, 2014

5/12/2014 Motors and Magnetic Field

Magnetic Motor
We connect the power supply to the motor and it began to spin.  When we reversed the direction of current it began to spin in the opposite direction.  


Homemade Magnetic Motor
We created a magnetic motor by using a copper wire, magnets, two paperclips, and a power supply. First we wrapped the wire as show in picture, then sanded 360 degrees of one lead of the wire and 180 degrees of the other lead to remove the paint on it. We attached the paper clips on the table and placed a magnet in between. Finally, we connect the power supply to the paperclips and rested the wire leads between the loops. When we turned on the power supply it began to spin which is caused by the current and magnetic field.  

The video of our homemade magnetic motor.  It works grate.  




Sunday, May 11, 2014

5/8/2014 Magnetic Force and Field

Activity 1: Field Directions Around a Bar Magnet
We are using a small compass to map out the magnetic field surrounding a large bar magnet and denote the directions of the field with arrows.  

A series of magnetic field lines with direction that point from north pole to south pole around the magnet.  We draw three closed loops which one loop enclose no magnetic pole(L1), another loop enclose one of the poles(L2), and another enclose both poles(L3) to show the net flux of each loops.  Recorded net flux in each loops on the right side of the picture.  

Actual magnetic field produce by the bar magnet.  


Activity 2: Calculate the Magnetic Field
Calculate the magnetic field produce by the U-shaped magnet acted on the copper hoop when current going through.  

 Using experiment data to calculate the magnetic field.  We have calculation error in calculating the force which Force in not equal to m*a+I*alpha.

I use the energy method to calculate the magnetic force.  

Tuesday, May 6, 2014

5/5/2014 Diodes and Transistors

One Transistor Amplifier
Base on the circuit as show to recreate a real circuit on the bread board.    

Using a 2N3904 transistor with resistors and capacitors to create an amplifier.

The two waves on the screen show the voltage supplied by the function generator(top wave) and its output(bottom wave) after amplification of the breadboard circuit.  By readying the result on the screen, we can say an amplification emitted about 100 times the original supplied.


Amplifier with Gain = 20 (Minimum Parts)
Base on the this circuit diagram to create an amplifier with a signal semiconductor.  

 The amplifier that we created on the bread board.  


Connecting the amplifier with power supply and speaker to play music from cell phone.  After we try to connect to several different speaker, we finally heard the music that playing on my phone from the speaker.  





Sunday, May 4, 2014

4/30/2014 Electronics

Active 1: Sound from a Function Generator
The set of connecting a speaker with the function generator as show in picture.  When we change the frequency of the function generator, the pitch of the sound changes.   When we change the amplitude of the function generator, the volume of the sound changes.   


Active 2: The Vertical Voltage Axis
Connecting a tap key and battery with oscilloscope.  Determine the voltage of the battery by readying the oscilloscope.  First, we set the VOLTS/DIV of CH1 to 0.5V, the line show on the screen moved 3 units up when the tap key is closed.  We can write a equation with this data as 3*0.5V=1.5V.  


Activity 3: Lissajous Figures
This time we connected the AC Transformer to the oscilloscope on CH 1 and the Function Generator on CH 2. The function generator was set to 60 Hz and AC Transformer was set to 30Hz.  When we set the oscilloscope in the XY mode we could see Lissajous Figures of the to channels. 

 When the function generator was set to 60 Hz and AC Transformer was set to 60Hz.

When the function generator was set to 60 Hz and AC Transformer was set to 90Hz.

When the function generator was set to 60 Hz and AC Transformer was set to 120Hz.


Activity 4: Mystery Box

We were given a mystery box and told to determine which waves or frequencies it consisted of.